MMM777NNNCCCDDD UUUllltttrrraaa i FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class
8Pin Assignment Pin Assignment 1 Ground 2 TX+ 3 TX- 4 Ground 5 RX- 6 RX+ 1234567 JSATA1/ JSATA2 7 Ground Power Connectors: JATXPWER1 PIN Ass
9Front Panel Connector: JPANEL1 Power Source Selection for Keyboard/ Mouse: JKBV1 JKBV1 Assignment Description 13 Pin 1-2 close +5V +5V for keyb
10Power Source Selection for USB: JUSBV1/ JUSBV2/ JUSBV4 JUSBV1/JUSBV2/ JUSBV4 Assignment Description 1 3 Pin 1-2 close +5V JUSBV1: 5V for JUSB1 p
11※ Clear CMOS Procedures: 1. Remove AC power line. 2. Set the jumper to “Pin 2-3 Close”. 3. Wait for five seconds. 4. Se
12System Operation Mode: JCLK3 Note: When overclock function failed and system is unable to boot-up, please follow the instruction b
13Deutsch Spezifikationen von M7NCD Ultra A. Hardware CPU Unterstützung für Sockel 462. Unterstützung für den AMD® Prozessor bis zu XP 3200
14Onboard-Peripheriegeräte a. Rückwand 2 Seriell-Ports. 1 parallele Schnittstelle. (SPP/EPP/ECP-Modus) 1 horizontales Audio-Port. 1 LAN-Port.
15 Einstellung der Jumper Die Abbildung verdeutlicht, wie Jumper eingestellt werden. Pins werden durch die Jumper-Kappe verdeckt, ist der Jumper ”
16CPU-Lüfter Headers: JCFAN1 Pin Belegung 1 Masse 2 +12V 1 JCFAN1 3 Sensor System-Lüfter Headers: JSFAN1 Pin Belegung 1 Masse 2 +12V 1 JSFAN1 3
17 Installation von DDR-Modul 1. Öffnen Sie einen DIMM-Slots, indem Sie die seitlich Chips nach außen drücken. Richten Sie das DIMM-Modul so üb
CCCooonnnttteeennnttt iiLAYOUT OF M7NCD ULTRA ...1 COMPONENT INDEX...
18Dieser Chip bietet zwei Serial-ATA-Kanäle sowie einen Parallel-ATA-Kanal für bis zu zwei Geräte. Es entspriecht der Speczifikation von SATA 1
19Wake On LAN Header: JWOL1 Pin Belegung 1 +5V_SB 2 Masse 1 JWOL1 3 Wake-up Stromversorgungsanschluss: JATXPWER1 PIN Belegung PIN Belegung 1 +3.3
20 Auswahl von Stromsversorgungsmodi für USB: JUSBV1/ JUSBV2/JUSBV4 JUSBV1/JUSBV2/ JUSBV4 Beschreibung Funktion 1 3 Pin 1-2 geschlossen +5V JUS
21※ Prozeß zum Löschen des CMOS: 1. Ausschalten Sie den AC-Netzstecker. 2. Lassen Sie Pin 2-3 von JCOMS1 geshclossen sein. 3. Bitte w
22System Operation Modus: JCLK3 Anmerkung: Wenn “Überspanng Funktion” nicht gelungen ist folgen Sie bitte die Instruktion darunter:
23Watchdog Technology It is important to know that when overclocking, the system can be at a vulnerable state. Therefore, the BIOSTAR Watchdog Te
24StudioFun! Introduction StudioFun! is a media-player based on optimized GNU/Linux distribution. It plays DVD, VCD, MP3, Audio CD and various oth
25Installation This option will do the basic installation of the distribution. The installation works on pre-installed windows or GNU/Linux distri
26Recovery In case of a MBR corruption, this option should be used. It will automatically probe the hard disk master boot record and find out the
27After complete boot up, you get to the main Desktop screen. The following section is a complete description of the Desktop application. Desktop
1Layout of M7NCD Ultra ※NOTE: ●represents the first pin.
28present in the DVD/CD-ROM drive. 2. DVD This control will glow whenever a DVD is detected in a DVD drive. The DVD will be auto-played only when
291. Select Region Clicking this icon will invoke the application for selection DVD region settings. Refer to section 5.2 Select DVD Region appli
30Software Details XINE XINE is a multimedia player. It plays back Audio CD, DVD, and VCD. It also decodes multimedia files like AVI, MOV, WMV, an
31f. MPEG-Video (.mpv, .m2v) g. MPEG-Audio (.mp2, .mp3) h. WAV (.wav) Video Codecs i. MPEG 1/2 j. MPEG 4 (aka OpenDivX) k. MS MPEG 4 a. Chapte
32l. j. Select hide button to hide the control panel of the player m. k. Select menu button to use menu’s while playing DVD n. l. Select contro
33 Screensaver Screensaver The xscreensaver daemon waits until the keyboard and mouse have been idle for a period, and then runs a graphics demo
342. Only one Screen Saver: When user chooses this option, screensaver displays only one graphics demo. 3. Blank Screen Only: When user chooses th
35three resolutions. • 640x480 • 800x600 • 1024x768 The current resolution of the Display will be selected by default. It requires restart of the
37Trouble Shooting PROBABLE SOLUTION No power to the system at all Power light don’t illuminate, fan inside power supply does not turn on. Indicat
2Component Index A. 5V/5VSB Selection for Keyboard L. Front USB Header (JUSB1) and mouse (JKBV1) M. Front USB Header
38 Problemlösung MÖGLICHE URSACHE LÖSUNG Das System hat keine Spannungsversorgung. Die Stromanzeige leuchtet nicht, der Lüfter im Innere
39 09/29/2003
3English M7NCD Ultra Features A. Hardware CPU Provides Socket-462. Supports the AMD® processor up to XP 3200+. Front Side Bus at 266
4On Board Peripherals a. Rear side 2 serial ports. 1 parallel port. (SPP/EPP/ECP mode) Audio ports in horizontal position. 1 LAN port. (optio
5How to setup Jumper The illustration shows how jumpers are setup. When the Jumper cap is placed on pins, the jumper is “close”. If no jumper cap
6CPU Fan Header: JCFAN1 Pin No. Assignment 1 Ground 2 +12V 1 JCFAN1 3 Sense System Fan Header: JSFAN1 Pin No. Assignment 1 Ground 2 +12V 1 JSFA
7 Installing DDR Module 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the
Comments to this Manuals